PPjla13 Single 10" Loaded Subwoofer Enclosure And Amp Package | Bass Packages

Description

About This Product
Description
JL Audio PPJLA13 Single 10" Loaded Subwoofer Enclosure and Amp Package
Package Includes:
One – JL Audio 10W1v3-4 10" Subwoofer
One – JL Audio JD250/1 Mono Amplifier
One – Single 10" Sealed Sub Enclosure
JL Audio 10W1v3-4 10" Subwoofer – 4 Ohm
The 10W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (4.6 in. / 117 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 10-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio’s proprietary technologies enhance its performance and reliability.
The 10W1v3-4 is best used with amplifier power in the 75W – 300W range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure.
General Specifications
Continuous Power Handling (RMS): 300 W
Recommended RMS Amplifier Powe: 75 – 300 W
Nominal Impedance (Znom): 4 Ω
Physical Specifications
Nominal Diameter 10.0 in / 250 mm
Overall Diameter (A) 10.5 in / 267 mm
Mounting Hole Diameter (B) 9.0625 in / 230 mm
Bolt Hole Circle (C) 9.7 in / 246 mm
Magnet Diameter (D) 4.92 in / 125 mm
Mounting Depth (E) 4.6 in / 117 mm
Driver Displacement 0.037 cu ft / 1.05 L
Net Weight 9.9 lb / 4.5 kg
Parameters
Free Air Resonance (Fs) 26.15 Hz
Electrical “Q” (Qes) 0.475
Mechanical “Q” (Qms) 7.243
Total Speaker “Q” (Qts) 0.446
Equivalent Compliance (Vas) 1.533 cu ft / 43.41 L
One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm
Reference Efficiency (no) 0.1600%
Efficiency (1 W / 1 m)** 84.2 dB SPL
Effective Piston Area (Sd) 53.584 sq in / 0.0346 sq m
DC Resistance (Re) 3.902 Ω
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.
JL Audio JD250/1 Monoblock Class D Subwoofer 250 Watt Amplifier
Designed to produce a healthy 250 watts into 2 ohms (14.4V, 1% THD), the JD250/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. Our proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion.
The JD250/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The JD250/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you easily set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.
Specifications
Rated Continuous (RMS) Power @ 14.4 V
@ 4 Ω: 150 W RMS x 1
@ 3 Ω: 200 W RMS x 1
@ 2 Ω: 250 W RMS x 1
@ 1.5 Ω: N/A
Rated Continuous (RMS) Power @ 12.5 V
@ 4 Ω: 115 W RMS x 1
@ 3 Ω: 150 W RMS x 1
@ 2 Ω: 200 W RMS x 1
@ 1.5 Ω: N/A
General Specifications
Frequency Response: 7 Hz – 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power: >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W: >60 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Damping Factor @ 4 Ω: >1000 / 50 Hz
Damping Factor @ 2 Ω: >500 / 50 Hz
THD+N @ Rated Power:
Input Voltage Range @ RCA Inputs: Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge: 8 AWG wire
Fuse Rating: 30 A (AFS, AGU or MaxiFuse™)
Signal Processing
Filter Mode(s): Low-Pass only
Filter Slope(s): 12 dB/octave
Filter Frequency Range: 50 Hz – 500 Hz
Detented, Calibrated Filter Freq. Potentiometer: No
Filter Defeat Function: No
Infrasonic Filter: No
Bass Boost EQ: Yes
Output Polarity Switch: No
Remote Subwoofer Level Control: Optional (RBC-1)
Remote Bass EQ Boost Control: No
Pass-Through Preamp Output: Buffered
Physical Specifications
Height (H): 2.10 in / 53 mm
Width (W): 9.50 in / 242 mm
Depth (D): 7.50 in / 190 mm